2020 Alfa Romeo Giulia TSBs

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure.

the radio: "Battery of Uconnect Box requires service. SOS call and related functions may be unavailable. Please visit an authorized dealer." PLEASE do not Replace the TBM module, only replace TBM Internal Battery (inside Telematics Box Module) and order PN68493347

Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): B1E21-96 - Backup Battery Component Internal Failure

Canister, only replace the ESIM Detector. -Before replacing the Vapor Canister due to Hard to Fill condition, replicate the condition at the Gas Station. If the condition is replicated, then check: 1) for kinked or pinched Clean Air Hose between the ESIM and the EVAP Air Filter; 2) for plugged EVAP Air Filter; 3) for kinked or pinched Vapor Hose between the Fuel Tank and the Vapor Canister. If the EVAP Filter is restricted, the replace the Filter. -Check if the Vapor Canister is flooded with fuel or the Recirculation Line has fuel. If fuel is found in the Vapor Canister or the Recirculation Line, then drop the Fuel Tank, remove the FDM Lock Ring to check if the internal Vapor Line is properly connected to the FDM Port. If the Vapor Line is not connected, then drain the fuel from the internal Vapor Line and properly connect to the FDM. Replace the Vapor Canister and the ESIM."

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0072-00 - Ambient Air Temperature Sensor Circuit Low. P0073-00 - Ambient Air Temperature Sensor Circuit High. P00B2-00 - Radiator Coolant Temperature Sensor Circuit Range-performance. P0607-00 - Control Module Performance. The customer may also experience the following: Vehicle is in limp mode REPAIR SUMMARY: This bulletin involves reprogramming the PCM with the latest available software. "

illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): P0072-00 - Ambient Air Temperature Sensor Circuit Low. P0073-00 - Ambient Air Temperature Sensor Circuit High. P00B2-00 - Radiator Coolant Temperature Sensor Circuit Range-performance. P0607-00 - Control Module Performance. REPAIR SUMMARY: This bulletin involves reprogramming the PCM with the latest available software."

Battery Charging Message, Presence of IBS Related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

only replace the EVAPORATIVE SYSTEM INTEGRITY MODULE DETECTOR.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On "

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

to confirm part number and applicability. There is an error with the wiring diagrams in Service Library that is causing the incorrect repair kit part number to populate. Please use the Mopar Connector Repair Kit Website until this issue is resolved.

Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find the following Diagnostic Trouble Code (DTC)U148A-86 - Implausible Data Received From Driver Assistance System Module (DASM) Signal Invalid. The customer may describe the following:Instrument Panel Cluster (IPC) disable icon switches on warnings for the ForwardCollision Warning (FCW) informing the driver ?Heads-up Warning Array (HWA) Unavailable Service Required?.The system starts working again automatically after a few seconds and/or up to 5 minutes.

regarding the latest Flash Over The Air (FOTA) update and provides the service technician an overview of the steps a customer will need to take to complete the update. Estimated National launch date for 1st FOTA update is expected on 07/22/2022. 2nd FOTA 1-2 weeks after 1st FOTA completes: 1st step from 3.8i to 3.8j2+ and 2nd step 3.8j2+ to 4.30. No dealership visit required, send 2 step TBM updates over the air. Customers may experience one or more of the following: Message displayed on the radio screen, "Uconnect Box requires service. Please visit an authorized dealer."Fig.1. Error Message Remote operation is not working. If the vehicle?s ignition is off state more than 7 days and less than 21 days, Remote ops do not work. Vehicle info is not working (or vehicle info is not giving correct information). Vehicle finder is not working.

software level MV-119.001.009The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the OwnerHandbook of the infotainment module. Some customers may experience one or more of the following:Radio may reboot while driving. Radio will display maintenance at the wrong mileage.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B1006-49 - Camera - Internal Electronic Failure. C141C-86 - Video Camera Private Can Communication Failure - Signal Invalid. C1999-86 - Data set Failure-Signal Invalid. In addition, the customer may notice the following: The Electronic Vehicle Information Center (EVIC) displays "Forward Collision Warning (FCW) Limited Functionality Front Camera Service Required"

DTC B1938-64 Humidity Sensor LIN Bus ? Signal Plausibility Failure

Upon further investigation, one or more of the following fault codes may be set in the PCM:

If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content

Customers may experience the following:When using the remote start feature after the vehicle has completely cooled down or left an extended period of time, the vehicle will start remotely and then shut off.

is operable and possibly reprogramming the DSCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set in the Drive Style Control Module (DSCM):U1700-87 - Body Control Module (BCM) - Missing Message. U0011-14 - Down Rotary Knob Failure-Circuit Short To Ground Or Open. U0011-15 - Down Rotary Knob Failure-Circuit Short To Battery Or Open. U0012-14 - Up Rotary Knob Failure-Circuit Short To Ground Or Open. U0012-15 - Up Rotary Knob Failure-Circuit Short To Battery Or Open. B1603-68 - Rotary Encoder Fault-Event Information. The following DTC has been set in the Body Control Module (BCM):U1A18-87 - DSCM (Drive Style Control Module) - Missing Message. The customer may also comment on the following:The vehicle dynamic (DNA) selector is inoperable.

Upon further investigation, one or more of the following fault codes may be set in the PCM:

Lane Departure And Blindspot Warning Displayed In The Cluster

Customers may experience the following:When using the remote start feature after the vehicle has completely cooled down or left an extended period of time, the vehicle will start remotely and then shut off.

is operable and possibly reprogramming the DSCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set in the Drive Style Control Module (DSCM):U1700-87 - Body Control Module (BCM) - Missing Message. U0011-14 - Down Rotary Knob Failure-Circuit Short To Ground Or Open. U0011-15 - Down Rotary Knob Failure-Circuit Short To Battery Or Open. U0012-14 - Up Rotary Knob Failure-Circuit Short To Ground Or Open. U0012-15 - Up Rotary Knob Failure-Circuit Short To Battery Or Open. B1603-68 - Rotary Encoder Fault-Event Information. The following DTC has been set in the Body Control Module (BCM):U1A18-87 - DSCM (Drive Style Control Module) - Missing Message. The customer may also comment on the following:The vehicle dynamic (DNA) selector is inoperable.

is operable and possibly reprogramming the DSCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U1700-87 - Body Control Module (BCM) - Missing Message. U0011-14 - Down Rotary Knob Failure-Circuit Short To Ground Or Open. U0011-15 - Down Rotary Knob Failure-Circuit Short To Battery Or Open. U0012-14 - Up Rotary Knob Failure-Circuit Short To Ground Or Open. U0012-15 - Up Rotary Knob Failure-Circuit Short To Battery Or Open. B1603-68 - Rotary Encoder Fault-Event Information. The following DTC has been set in the Body Control Module (BCM):U1A18-87 - DSCM (Drive Style Control Module) - Missing Message. The customer may also comment on the following:The vehicle dynamic (DNA) selector is inoperable.

is operable and possibly reprogramming the DSCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U1700-87 - Body Control Module (BCM) - Missing Message. U0011-14 - Down Rotary Knob Failure-Circuit Short To Ground Or Open. U0011-15 - Down Rotary Knob Failure-Circuit Short To Battery Or Open. U0012-14 - Up Rotary Knob Failure-Circuit Short To Ground Or Open. U0012-15 - Up Rotary Knob Failure-Circuit Short To Battery Or Open. B1603-68 - Rotary Encoder Fault-Event Information. The following DTC has been set in the Body Control Module (BCM): U1A18-87 - DSCM (Drive Style Control Module) - Missing Message. The customer may also comment on the following:The vehicle dynamic (DNA) selector is inoperable.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC)U148A-86 - Implausible Data Received From Driver Assistance System Module (DASM) Signal Invalid. The customer may describe the following: Instrument Panel Cluster (IPC) disable icon switches on warnings for the Forward Collision Warning (FCW) informing the driver ?Heads-up Warning Array (HWA) Unavailable Service Required?.The system starts working again automatically after a few seconds and/or up to 5 minutes.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B1006-49 - Camera - Internal Electronic Failure. C141C-86 - Video Camera Private Can Communication Failure - Signal Invalid. C1999-86 - Data set Failure-Signal Invalid. In addition, the customer may notice the following: The Electronic Vehicle Information Center (EVIC) displays "Forward Collision Warning (FCW) Limited Functionality Front Camera Service Required"

DTC B1938-64 Humidity Sensor LIN Bus ? Signal Plausibility Failure

software level MV-119.001.009The customer should be informed that after the reprogram, the radio will need to have the phones paired to the Entertainment Telematics Module (ETM). The operative details for pairing telephones and settings are shown in the OwnerHandbook of the infotainment module. Some customers may experience one or more of the following:Radio may reboot while driving. Radio will display maintenance at the wrong mileage.

replacing the HALF module (forward-facing camera module) refer to STAR ONLINE S2008000001: During PDI inspection you may find the FCW Limited Functionality message displayed in the EVIC. Upon scanning the vehicle for DTC?s you may find: 1) B1006-49 HALF ECU - Internal electronic failure C141C-86 Video camera private CAN communication failure - Signal invalid C1999-86 Dataset failure - Signal invalid If you are unable to clear the combined three DTC's and the EVIC displays, "FCW LIMITED AVAIL", Perform a ?Restore Proxy Configuration? under Guided Diagnostics in the left hand column of WiTech 2. After performing this procedure, the DTC?s should go to ?Stored? and can then be cleared. The FFCM was flashed in transit on these vehicles and the Restore Proxy Config procedure was never performed. The Restore Proxy Configuration is needed to complete the flash process. 2) B1007-54 Camera - Missing Calibration If you are unable to calibrate the HALF Module, via the procedure in the service manual, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary.

Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set:B1006-49 - Camera - Internal Electronic Failure. C141C-86 - Video Camera Private Can Communication Failure - Signal Invalid. C1999-86 - Dataset Failure-Signal Invalid. In addition, the customer may notice the following:The Electronic Vehicle Information Center (EVIC) displays "Forward Collision Warning (FCW) Limited Functionality Front Camera Service Required"Fig.1.EVIC FCW Message

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles) This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter.

845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.

Before replacing this part due to Engine Light On with P1CEA (Boost Side EVAP Purge System Performance), check for: 1) Improperly connected or kinked/pinched Purge Hoses at the Ejector Tees on the Air Box or Duct. 2) Improperly connected or kinked/pinched Purge Hose at the Purge Solenoid or OBD Valve. 3) Improperly connected or kinked/pinched Purge Hose at the Intake. 4) Check for the correct Purge Hoses installation.

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure."

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure."

Once the claimed fault is confirmed, check the severity of the leak and replace the timing cover sealant, if necessary, according to the Repair Procedure. "

the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles). This bulletin involves resetting the oil life monitor and if necessary changing the engine oil and filter."

Upon further investigation, a P1CEA - Boost Side Evap Purge System Performance DTC may be set in the PCM with no other DTCs set.

installed in the vehicle.

control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with the following Diagnostic Trouble Code (DTC) or the symptom/conditions listed below: B10C8-36 - Cabin Fan Brushless - Signal Frequency Too Low. The HVAC fan stops working after a Engine Start/Stop (ESS) function.

Engine misfires.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

Engine misfires.

Engine misfires.

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

(ETL, ETM, ETN Engines)

control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with the following Diagnostic Trouble Code (DTC) or the symptom/conditions listed below: B10C8-36 - Cabin Fan Brushless - Signal Frequency Too Low. The HVAC fan stops working after a Engine Start/Stop (ESS) function.

control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with the following Diagnostic Trouble Code (DTC) or the symptom/conditions listed below: B10C8-36 - Cabin Fan Brushless - Signal Frequency Too Low. The HVAC fan stops working after a Engine Start/Stop (ESS) function.

Upon further investigation, a P1CEA - Boost Side Evap Purge System Performance DTC may be set in the PCM with no other DTCs set.

installed in the vehicle.

Start Stop Unavailable, ACC Unavailable Service Required Messages. C1452-86 Engine Torque DASM- Signal Invalid

All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with the following Diagnostic Trouble Code (DTC) or the symptom/conditions listed below: B10C8-36 - Cabin Fan Brushless - Signal Frequency Too Low. The HVAC fan stops working after a Engine Start/Stop (ESS) function.

The customer may experience the oil change light illuminated on the dash shortly after taking delivery of the vehicle within 6,437 Km (4,000 miles).

control module with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination with the following Diagnostic Trouble Code (DTC) or the symptom/conditions listed below:B10C8-36 - Cabin Fan Brushless - Signal Frequency Too Low. The HVAC fan stops working after a Engine Start/Stop (ESS) function.

Upon further investigation there may be a fault code for P0300 -Multiple Cylinder Misfire DTC pending, stored, or active in the Powertrain Control Module (PCM).

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

Fault code P0244- TURBOCHARGER/SUPERCHARGER WASTEGATE SOLENOID "A" RANGE/PERFORMANCE is set in the Powertrain Control Module (PCM a.k.a. ECM) after the turbocharger assembly has been replaced.

The o-ring is serviced separately and complete turbo replacement may not be necessary.

this is normal and not a defect.

semi and full synthetic oils.

Detected Message

Detected Message

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates

Cluster (IPC)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Verify current warranty policy to determine if digital imaging pre-authorization is required or pre-approval is required from the Regional Office; depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels."

Cluster (IPC)

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: **Verify current warranty policy to determine if digital imaging pre authorization is required or Pre Approval is required from Regional Office depending on market.** This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

exterior surface areas of the hinges, doors, fenders, swing gates or liftgates. NOTE: Digital imaging pre authorization is required for Smart Warranty Base dealers or Pre Approval is required from Regional Office depending on market. This bulletin involves inspecting and if necessary removing corrosion and refinishing the suspect aluminum panels on the vehicle, hood, door, fenders, hinges, swing gates or liftgate panels.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.

B)

TBM Setting Stored Or Pending DTCs B22A9, B1560, B1561, B1562

information is displayed on the performance page. This bulletin involves inspecting the software level to see if the radio needs one or two USB flash drive(s) to update the radio software level to 131.010.002. CAUTION! The repair procedure must be followed step by step. If the radio is not updated with the correct software level at the correct time the radio can be damaged or the updates won?t complete.

If the Filter is restricted or blocked then replace the part. For customers that drive light duty trucks in extreme dusty and dirty road conditions, please reference information only TSB 25-009-24 for an available MOPAR Dual EVAP Filter kit that is customer paid.

Rev A

Alignment Pins Not Properly Seated

"

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Android Auto and Apple Carplay applications may not operate with the vehicle if an aftermarket cable is being used. Verify the functionality of these applications using an OEM Apple Lightning cable or an OEM provided USB cable for Android phones before performing any additional troubleshooting. For questions regarding Android Auto or Apply Carplay functionality, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.

Order a "Z" part number for all Exchange Orders: Warranty, Mopar, Customer pay and Service contract. Order a "68" part number for New unsold units only.

Library for specifications so a suitable alternative can be used

system